Densities are approximate. Your supplier can give the exact figure.
Enter valid measurements to see how much gravel you need.
Gravel needed (with extra)
–m³
–
Area covered
–
Volume without extra
–
Weight (tonnes)
–
Weight (US tons)
–
Weight (lb)
–
Volume (cubic feet)
–
Estimated material cost
–
Gravel Calculator
Planning a driveway, walkway, garden path, or landscaping project? Our gravel calculator helps you estimate how much gravel you need based on your project’s dimensions and desired depth. By entering the length, width, and depth of the area, you can calculate the required volume in cubic feet or cubic yards and estimate the approximate weight in tons.
Whether you’re spreading gravel over a small garden bed or building a large gravel driveway, an accurate estimate helps you order the right amount of material, reduce waste, and manage your budget. This guide explains how to calculate gravel, compare different gravel types, estimate material costs, and understand the difference between loose and compacted gravel.
Your Gravel Estimate
Your gravel estimate depends on the size of the area, the required depth, and the density of the material you choose. A reliable estimate includes the total volume, approximate weight, and an allowance for compaction or uneven ground when necessary.
To calculate your gravel requirements, collect these measurements:
- Length: The distance from one end of the project to the other.
- Width: The distance across the area.
- Depth: How thick the gravel layer should be after installation.
- Gravel type: Different aggregates have different densities, which affect the estimated weight.
- Extra material: Consider additional gravel for compaction, uneven surfaces, and minor measurement errors.
For example, a rectangular driveway measuring 20 feet long and 12 feet wide with a gravel depth of 4 inches requires approximately 2.96 cubic yards of gravel before any additional allowance.
This estimate represents the geometric volume. The actual delivered weight depends on the gravel’s density, moisture content, and grading.
How to Use
Using a gravel calculator is straightforward. Follow these steps to estimate the material required for your project.
- Measure the length: Measure the full length of the area in feet.
- Measure the width: Record the width of the area in feet.
- Choose the gravel depth: Enter the desired thickness in inches or feet. Remember that 4 inches equals one-third of a foot.
- Select the shape: Use the appropriate calculation for a rectangular, circular, triangular, or irregular area.
- Choose the gravel type: Select a suitable aggregate and density if you want to estimate weight in addition to volume.
- Calculate the volume: Multiply the area by the gravel depth to determine the required volume.
- Estimate the weight and cost: Convert the volume to tons using the selected density, then multiply the estimated quantity by the supplier’s price.
Always verify whether your supplier sells gravel by the cubic yard, short ton, or another unit. This ensures your calculated quantity matches the supplier’s pricing method.
How Much Gravel Do I Need?
The amount of gravel you need depends mainly on the surface area and the thickness of the gravel layer. Larger areas and deeper layers require more material.
For a rectangular area, use this formula:
Gravel volume in cubic feet = Length × Width × Depth in feet
To convert cubic feet into cubic yards, divide the result by 27 because one cubic yard contains 27 cubic feet.
Example: Suppose your garden path is 15 feet long, 4 feet wide, and 3 inches deep.
First, convert the depth into feet:
3 ÷ 12 = 0.25 feet
Calculate the volume:
15 × 4 × 0.25 = 15 cubic feet
Convert to cubic yards:
15 ÷ 27 = 0.56 cubic yards
You need approximately 0.56 cubic yards of gravel before allowing for compaction, uneven ground, or waste.
For a more practical order, check your supplier’s minimum delivery quantity and consider whether the project requires a base layer and a separate finishing layer.
Example Two-Layer Gravel Driveway
A two-layer gravel driveway typically has a compacted base layer for stability and a top layer for a smooth, attractive driving surface. The total quantity must be calculated separately for each layer.
Suppose a driveway is 40 feet long and 12 feet wide. You plan to install a 6-inch base layer and a 2-inch top layer.
Step 1: Calculate the driveway area.
40 × 12 = 480 square feet
Step 2: Calculate the base layer.
Convert 6 inches to feet:
6 ÷ 12 = 0.5 feet
Volume:
480 × 0.5 = 240 cubic feet
Convert to cubic yards:
240 ÷ 27 = 8.89 cubic yards
Step 3: Calculate the top layer.
Convert 2 inches to feet:
2 ÷ 12 = 0.167 feet, approximately
Volume:
480 × 0.167 = 80 cubic feet, approximately
Convert to cubic yards:
80 ÷ 27 = 2.96 cubic yards, approximately
Step 4: Calculate the total volume.
8.89 + 2.96 = 11.85 cubic yards, approximately
The driveway requires approximately 11.85 cubic yards of gravel by geometric volume, before adjustments for compaction, material handling, and site conditions. Actual ordering quantities should be based on the specified compacted thickness and the supplier’s material recommendations.
How Much Gravel for a Driveway
The amount of gravel required for a driveway depends on its length, width, traffic load, soil conditions, and the thickness of each layer.
A small residential driveway may require only a few cubic yards, while a long driveway or one with a deep aggregate base may require substantially more.
Here is a quick reference for a rectangular driveway with a single gravel layer:
| Driveway size | Depth | Approximate volume |
| 10 × 20 feet | 3 inches | 1.85 cubic yards |
| 12 × 30 feet | 4 inches | 4.44 cubic yards |
| 12 × 40 feet | 6 inches | 8.89 cubic yards |
| 20 × 50 feet | 4 inches | 12.35 cubic yards |
| 20 × 100 feet | 6 inches | 37.04 cubic yards |
These figures are geometric volumes and do not include additional material for compaction, grading, or waste.
For a durable driveway, choose aggregate suitable for the soil and expected vehicle traffic. Angular crushed stone generally interlocks better than rounded gravel, making it useful for many driveway base and surface applications.
Loose Delivery Volume vs Compacted Depth
Loose delivery volume and compacted depth are not the same thing. Gravel can occupy more space when delivered loosely than it does after being spread and compacted.
For example, a driveway designed to have a 4-inch compacted gravel layer may require a thicker loose layer before compaction. The exact amount depends on the aggregate type, particle size, moisture, equipment, and installation method.
When ordering gravel, ask your supplier or contractor how the recommended quantity relates to the finished compacted depth. Some suppliers provide volume estimates, while others quote weight and use a typical bulk density.
Avoid applying an arbitrary compaction percentage to every gravel type. Instead, use project-specific guidance where available and allow for uneven ground or grading requirements separately.
Worked Examples: Three Shapes
Different project shapes require different area formulas. Once you calculate the surface area, multiply it by the depth in feet to determine the gravel volume.
Example 1: Rectangular area
A patio is 20 feet long and 10 feet wide, with a gravel depth of 4 inches.
- Area: 20 × 10 = 200 square feet
- Depth: 4 ÷ 12 = 0.333 feet, approximately
- Volume: 200 × 0.333 = 66.67 cubic feet, approximately
- Cubic yards: 66.67 ÷ 27 = 2.47 cubic yards, approximately
You need about 2.47 cubic yards of gravel before additional allowances.
Example 2: Circular area
A circular garden bed has a radius of 5 feet and a gravel depth of 3 inches.
The area of a circle is:
Area = π × Radius²
Calculate the area:
3.1416 × 5 × 5 = 78.54 square feet, approximately
Convert the depth:
3 ÷ 12 = 0.25 feet
Calculate the volume:
78.54 × 0.25 = 19.64 cubic feet, approximately
Convert to cubic yards:
19.64 ÷ 27 = 0.73 cubic yards, approximately
You need about 0.73 cubic yards of gravel before allowances.
Example 3: Triangular area
A triangular landscaping section has a base of 12 feet, a perpendicular height of 8 feet, and a gravel depth of 4 inches.
The area of a triangle is:
Area = ½ × Base × Height
Calculate the area:
0.5 × 12 × 8 = 48 square feet
Convert the depth:
4 ÷ 12 = 0.333 feet, approximately
Calculate the volume:
48 × 0.333 = 16 cubic feet, approximately
Convert to cubic yards:
16 ÷ 27 = 0.59 cubic yards, approximately
You need about 0.59 cubic yards of gravel before allowances.
After You Estimate Your Gravel
Once you know the required volume, take a few additional steps before placing your order.
- Confirm the final dimensions and desired finished depth.
- Determine whether the project needs a compacted base and a separate top layer.
- Select a gravel type suitable for the project’s purpose.
- Convert the estimated volume into weight if the supplier sells by the ton.
- Request a delivered price that includes transportation and any applicable fees.
- Check the minimum delivery quantity and whether the supplier offers partial loads.
- Plan where the truck will unload the gravel and how the material will be spread.
For larger projects, compare quotes from multiple local suppliers. Prices can vary considerably depending on the aggregate source, delivery distance, quantity, and regional market conditions.
Gravel Types and Densities
Gravel comes in several sizes and compositions. The right choice depends on drainage, stability, appearance, traffic, and the purpose of the project.
Bulk density is particularly important when converting cubic yards into tons. The following figures are illustrative estimating ranges, not guaranteed specifications. Actual densities vary with gradation, moisture, source, and compaction.
| Gravel or aggregate type | Approximate bulk density |
| Pea gravel | 2,400–2,800 lb/yd³ |
| Crushed stone | 2,500–3,000 lb/yd³ |
| #57 stone | 2,400–2,900 lb/yd³ |
| Road base or crusher run | 2,600–3,200 lb/yd³ |
| Drainage gravel | 2,400–2,900 lb/yd³ |
| Decorative gravel | 2,300–2,900 lb/yd³ |
Use the density supplied by your aggregate supplier whenever possible. A calculator’s default density is only an estimate and should not replace the product’s actual bulk-density information.
Common gravel types include:
- Pea gravel: Small, rounded stones used for garden paths, decorative areas, and some drainage applications.
- Crushed stone: Angular aggregate commonly used for driveways, walkways, and construction bases.
- Road base: A mixture of aggregate sizes, often including fines, designed to compact into a stable base.
- Drainage gravel: Clean, appropriately graded aggregate used in drainage systems when specified.
- Decorative gravel: Colored or naturally attractive stone used for landscaping and garden beds.
Choose the aggregate based on the intended use rather than density alone.
What Is #57 Gravel?
#57 gravel, also called #57 stone, is a commonly used graded crushed-stone aggregate in the United States. It is often used for drainage, construction, landscaping, and driveway projects where the specified material is appropriate.
Under commonly used ASTM C33 aggregate sizing conventions, No. 57 aggregate is generally associated with a size range passing a 1½-inch sieve and retained on a No. 4 sieve. Actual gradation requirements depend on the applicable specification and supplier.
Because #57 stone generally has little fine material compared with dense-graded road base, it does not compact and interlock in exactly the same way as crusher run. Its suitability depends on the intended application and the design requirements.
Typical uses include:
- Drainage layers around suitable foundations and other structures.
- Landscaping beds and decorative stone areas.
- Certain driveway applications when the design calls for clean crushed stone.
- Construction and drainage projects requiring a specified aggregate gradation.
For estimating, a rough bulk-density range of 2,400–2,900 pounds per cubic yard can be used as an initial reference. Ask the supplier for the actual density of the material being delivered.
Gravel Coverage Quick Reference
Gravel coverage depends on the quantity purchased and the depth at which it is spread. The following table shows the approximate area covered by one cubic yard of gravel before allowances for compaction, uneven surfaces, and waste.
| Gravel depth | Approximate coverage per cubic yard |
| 1 inch | 324 square feet |
| 2 inches | 162 square feet |
| 3 inches | 108 square feet |
| 4 inches | 81 square feet |
| 6 inches | 54 square feet |
| 8 inches | 40.5 square feet |
| 12 inches | 27 square feet |
These values assume a uniform layer and use 27 cubic feet per cubic yard.
For example, one cubic yard of gravel spread at a depth of 3 inches covers approximately 108 square feet. If your area is 216 square feet, you would need approximately 2 cubic yards at that depth before additional allowances.
Tons to Cubic Yards Conversion by Gravel Type
Converting tons to cubic yards requires the bulk density of the gravel. Because different aggregates have different densities, one ton of pea gravel may occupy a different volume from one ton of road base.
In the United States, a short ton equals 2,000 pounds.
Cubic yards = Tons × 2,000 ÷ Bulk density in pounds per cubic yard
Using an illustrative density of 2,700 pounds per cubic yard:
1 ton × 2,000 ÷ 2,700 = 0.74 cubic yards, approximately
The following table uses illustrative densities for comparison.
| Material | Assumed density | Approximate cubic yards per short ton |
| Pea gravel | 2,600 lb/yd³ | 0.77 |
| Crushed stone | 2,700 lb/yd³ | 0.74 |
| #57 stone | 2,650 lb/yd³ | 0.75 |
| Road base | 2,900 lb/yd³ | 0.69 |
| Drainage gravel | 2,650 lb/yd³ | 0.75 |
These figures are approximate. Use the density for your specific material when preparing a purchase order or delivery estimate.
Formulas
Gravel calculations use basic geometry to determine the volume of material required. The essential rule is to calculate the area first and then multiply it by the depth.
Rectangular area
Area = Length × Width
Circular area
Area = π × Radius²
Triangular area
Area = ½ × Base × Height
Gravel volume
Volume in cubic feet = Area in square feet × Depth in feet
Cubic feet to cubic yards Cubic yards = Cubic feet ÷ 27
Cubic yards to cubic feet Cubic feet = Cubic yards × 27
Volume to estimated weight
Weight in pounds = Volume in cubic yards × Bulk density in pounds per cubic yard
Pounds to US short tons
Short tons = Pounds ÷ 2,000
Tons directly from cubic yards
Short tons = Cubic yards × Bulk density ÷ 2,000
Estimated material cost
Material cost = Quantity purchased × Price per unit
For example, if a project requires 5 cubic yards of gravel and the supplier charges $55 per cubic yard, the estimated material cost is:
5 × $55 = $275
This amount excludes delivery, taxes, and any additional services.
Sizing & Material Standards
Selecting gravel involves more than calculating volume. Aggregate size, grading, material quality, and installation requirements also affect performance.
In the United States, ASTM International publishes standards for aggregates used in construction. ASTM C33/C33M addresses concrete aggregates, while other specifications apply to different materials and uses. The appropriate standard depends on the project and the material being purchased.
Consider the following factors:
- Particle size: Larger aggregate may be suitable for some drainage and base applications, while smaller material can be preferred for certain paths and decorative surfaces.
- Grading: A well-graded mixture may compact differently from uniformly sized, clean stone.
- Fines content: Fine particles influence compaction, drainage, and surface stability.
- Moisture content: Water affects the delivered weight and can influence handling and compaction.
- Installation depth: Required thickness depends on soil conditions, traffic loads, drainage, and the project’s design.
- Supplier specifications: Confirm the actual aggregate size and density rather than relying only on a product’s general name.
For driveways carrying regular vehicle traffic, a properly designed and compacted base is often important for long-term performance. When the project involves structural support, drainage requirements, or challenging soil, follow the recommendations of a qualified contractor or engineer.
How to Estimate Gravel Cost
Estimating gravel cost starts with the quantity you need and the price your supplier charges. The final project cost may also include delivery, site preparation, spreading, and compaction.
Use this process to prepare a practical budget.
Step 1: Calculate the required quantity.
Determine the volume in cubic yards and convert it into tons if necessary.
Step 2: Find the supplier’s unit price.
Ask whether the quoted price is per cubic yard, short ton, bag, or truckload.
Step 3: Calculate the material cost.
Multiply the quantity purchased by the price per unit.
Step 4: Add delivery charges.
Delivery may depend on distance, load size, access, and local supplier policies.
Step 5: Include installation expenses.
Consider equipment rental, labor, grading, excavation, geotextile fabric, and compaction if required.
Example:
Suppose you need 6 cubic yards of gravel at $50 per cubic yard. Delivery costs $90, and spreading costs $120.
- Material: 6 × $50 = $300
- Delivery: $90
- Spreading: $120
- Estimated total: $300 + $90 + $120 = $510
Your estimated project cost is $510 before taxes or other applicable fees.
Actual gravel prices vary by location, aggregate type, supplier, and order size. Obtain a current quote before purchasing, and confirm whether the delivered quantity is measured by volume or weight.
Frequently Asked Questions
How do I calculate how much gravel I need?
Multiply the area’s surface area by the desired depth in feet to calculate cubic feet. Divide the result by 27 to convert it to cubic yards. For irregular areas, divide the project into simpler shapes and add their volumes together.
How many cubic yards of gravel are in a ton?
The amount depends on the material’s bulk density. For gravel with an assumed density of 2,700 pounds per cubic yard, one US short ton occupies approximately 0.74 cubic yards. Use the supplier’s density for a more reliable estimate.
How much area does one cubic yard of gravel cover?
One cubic yard contains 27 cubic feet. At a depth of 3 inches, it covers approximately 108 square feet; at 4 inches, approximately 81 square feet; and at 6 inches, approximately 54 square feet.
How deep should gravel be for a driveway?
The required depth depends on the soil, vehicle loads, drainage, aggregate type, and driveway design. Some projects use separate base and surface layers. Follow local construction guidance or a qualified contractor’s recommendations instead of relying on a single depth for every driveway.
Is gravel sold by the ton or cubic yard?
Both methods are common in the United States. Some suppliers sell by the ton, while others quote cubic yards or truckloads. Confirm the unit, delivered quantity, and density assumptions before ordering.
Should I order extra gravel?
An allowance may be appropriate for uneven ground, grading, handling losses, or compaction. The amount depends on site conditions and the aggregate type. Where accurate quantities matter, ask the supplier or contractor to determine the additional amount rather than applying the same percentage to every project.
What is the difference between #57 gravel and crusher run?
#57 gravel is generally a clean, graded crushed stone with relatively little fine material. Crusher run typically contains a mixture of stone sizes and fines that can compact into a dense base. Their drainage and compaction characteristics differ, so choose according to the project’s requirements.
How do I calculate gravel cost?
Multiply the quantity you need by the supplier’s price per unit, then add delivery, preparation, and installation costs. Check whether the quoted price includes taxes or other fees.
Can I use a gravel calculator for a circular area?
Yes. Calculate the circular surface area using π × radius², then multiply by the gravel depth in feet. Divide the volume in cubic feet by 27 to obtain cubic yards.
How accurate is a gravel calculator?
A gravel calculator provides a mathematical estimate based on the dimensions and density entered. Actual quantities and weights may differ because of irregular surfaces, material grading, moisture, compaction, and supplier measurement practices. Accurate measurements and material-specific density data improve the estimate.
How do I convert inches of gravel depth into feet?
Divide the depth in inches by 12. For example, 3 inches equals 0.25 feet, 4 inches equals approximately 0.333 feet, and 6 inches equals 0.5 feet.
What type of gravel is best for a driveway?
The best option depends on soil conditions, drainage, traffic, and the desired finish. Angular crushed stone or a suitable graded base may provide stability, while a different aggregate may be selected for the surface. Ask a local supplier or contractor which material is appropriate for your site.
Can I calculate gravel for multiple layers?
Yes. Calculate the volume of each layer separately using its own depth, then add the volumes together. If different gravel types are used, estimate their weights and costs separately because their densities and prices may differ.
Conclusion
A gravel calculator makes it easier to estimate the material required for driveways, garden paths, patios, and landscaping projects. By measuring the area, converting depth into feet, calculating volume, and using the correct aggregate density, you can estimate cubic yards, approximate tons, and material costs before placing an order.
For the best results, verify your measurements, select a gravel type suited to your project, and confirm the density and delivery quantity with your supplier. A little planning helps you avoid unnecessary expense and order an appropriate amount of gravel for your next project.
